Cloning Marijuana simple, very consistent (about 95%) and
best of all under 20$

our links | growing
marijuana | legal highs | marijuana seeds |

Here is a step by step method for cloning, its is
simple, very consistent (about 95%) and best of all under 20$!!!!!
Actually about $12.00 you need a bag of perlite, one of vermiculite,
Rootone and a clear storage box 18L x 10W x 6T and some "pony pac"
containers (these are cheap container for nursery plants, you can get
them free if you ask what day they throw out the dead plants, and a
little bloom formula fertilizer most any brand is OK the count should be
about 5-12-8 or something like that with high potassium.

Step 1 - Select a cutting, you want a healthy piece not some
scraggly piece of crap, snip it off with a pair of very sharp scissors,
at this time mix the perlight and vermiculite at 50/50 mix and add
watertill is soft and wet, pack the containers full and firmly pack the
medium in.

Step 2 -
Remove the leaves and small side branches leaving a nice cluster on the
top of the cut.

Step 3
- Place the cut in a glass of water and 1/10
the strength bloom fertilizer.

Step 4
- Put the stripped cut end into the rooting
powder it should cling on real well because of the water fert mix make
sure its VERY well coated.

Step 5
- Take a pen and make a hole in the pre
prepaired mix and containers make it big so it wont scrape the rooting
hormone off.

Step 6 -
Place the cutting into the hole you made in step 5 and pack the medium
tightly around it.

Step 7 -
Using the bloom formula spray the cuts getting them pretty wet, now for
the storage box, tap holes on each side and two on top I like them to be
about 1/2 across, turn the box upside down place you containers with the
cuts on the lid and close it up,you will need to open it every other day
for a week or so, if its really hot or dry you can spray them also,after
a week take the lid off for a few hours at a time then just leave it
off, don't pull on the cuts or move them in any way this only slows
progress, you will have rooted cuts in two weeks or so they can go into
soil or hydro from there.

Here they are I removed the lid two
days ago,today they were wilting a little (that's good) so I gave them a
tiny bit of the 1/10th bloom mix, if you look carefully you can tell
witch are rooting already, they are the ones with the yellow leaves. I
haven't looked but they should all have bumps and starting roots by the
way they look on top,I made the mistake of putting them a little close
to the fan so two of them next to a hole got a little crisp but they
look like the will pull through....

Here are the same clones being pulled
from their container I usually let the go 14 days but I need the cloner
for the seedlings, the root development is very good but in a few more
days its a huge clump! Bigger roots leads to bigger yields, this is why
I wanted you to coat the stem so far up and with so much hormone...Be
very careful when you pull the clone out it should be packed in there
very snug, squeeze the sides of the pot and gently pull the stem as it
releases from the pot. The clones are going in soil I make a big hole so
as not to break the delicate roots. After they are in pack the soil
around them. If going to hydro with Rockwool put in hole in top of cube
and cover with flock if using gro rocks just carefully put them on a
single layer of rocks hold the and add rocks till the basket is
full.

Oh by the way the results were 100%
rooted I think if you were really looking to say this was fast they have
been rooted for three days at least but I think its better to let them
sit for a while (I like another four days longer than this time) this
greatly increases chances of healthy growth and minimum shock due to
transplanting.

Good luck cloners, have
fun!!!

Information supplied by:
webfish

| 1081 HV Amsterdam De
Boelelaan 1217 | [email-masked] | Last Updated
12/04/2003 | All Rights Reserved Copyright © 2003 Growing Marijuana
|